GU10 IP65 Directional Minimal Trim


£ 43.26

GU10 IP65 Directional Fire Rated Minimal Trim
GU10 IP65 Directional Fire Rated Minimal Trim
£ 48.91
£ 48.91
GU10 Directional Minimal Trim
GU10 Directional Minimal Trim
£ 38.41
£ 38.41

GU10 IP65 Directional Minimal Trim

IP65 architectural adjustable downlight with deep internal
baffle for GU10 Lamps (Lamp not included)

£ 43.26 43.26 GBP £ 43.26

£ 42.41

This combination does not exist.

Stock Code :
Share :

Product Description

The GU10 IP65 DIRECTIONAL Minimal Trim is a trimless recessed adjustable IP65 architectural downlight, with a deep internal baffle, which tilts by 35° and rotates by 360°, designed to fit a standard GU10 lamp. It sits proud of the ceiling by 3mm and is only 65mm in Diameter so is almost invisible in the ceiling, especially when used with paintable front plates, the luminaire provides visual comfort by reducing the glare.

This product is IP65 rated and is suitable for Zone 1, Zone 2 areas and outside use (see our Guide to IP Ratings). This version is non fire-rated (but 60-minute and 120-minute fire-rated versions are available). It is fully interchangeable with any of the products in the Levello range as all of the Levello products fit into the same housing. Luminaires and lamps can be swapped quickly and simply, should the need arise without damaging the ceiling.

Although we recommend Soraa Lamps or our light engines, this product can be used with almost any GU10 lamp as long as the diameter of the front of the lamp is less than 50mm. Ceiling void heights are calculated based on the Soraa lamp which is 53.5 mm high.

Technical Information

Physical Characteristics


Cut out                                          62 mm

Minimum Ceiling Void Depth    131 mm

  1. measured with 53.5 GU10 lamp - Measure your lamp


(excluding GU10 Lamp)             215 g


Housing: Mild steel galvanised & powder coated


Tilt angle       up to  35°

Rotation        360°

Technical Characteristics

Fire & Insulation

Non Fire-Rated

Not suitable for covering with  insulation

     (see insulation covering accessories)

Air Tightness

When used with a Thermahood conforms to 

  • C2 – Condensation
  • L1 – Insulation And Air Leakage
  • E1 – Sound Protection

 Standards & Ratings

BSEN 60958



5 years (Luminaire parts and materials)

Electrical Characteristics


3 Pole

16A screwless

Cable capacity

    4 x 1mm

    2 x 1.5mm

Lamp Suitability

25W Halogen


Product Features

Lighting Looking fabulous

Minimal Trim

Arguably one of the most discrete downlights available as it is only 3mm high and the Bezel has a diameter of 65mm

Paintable front plates

With our unique paintable front plate option the front of fitting blends in with the rest of the ceiling and more importantly won't become yellow with ageing, unlike other light fittings.

Wide range of accessories

Allowing you to customise not only the look of the light fitting, but also the light coming out of it. Check out our range of baffles, front plates, lenses and filters.

... simple to use and maintain

Easy maintenance

No spring clips, no complicated twist and lock fixing systems, just simple magnets, pull the insert out and swap the lamp or even change the fitting.


Should you or your client need to change how the space is used, the light fitting can be quickly and easily swapped for one of our other products such as a pendant.

IP65 Protection

This product is suitable for Zone 1, Zone 2 areas and outside use. IP65 means it will withstand jets of water

35° Tilt, 360° Rotation

The mechanism is completely recessed in the ceiling and can tilt by 35° and rotate by 360°

What's in the box

This product has everything you need to install and fit our product with the exception of the GU10 lamp

First Fix Housing

The Housing complete with the supply connector and  installation instructions

GU10 Lampholder and Connector

The "plug and play" GU10 Lampholder is pre-wired for your  convenience

Directional Insert

The Directional insert is supplied with a spring clip to fix the lamp into the insert

IP65 Front Plate

The IP65 front plate has glass bonded in between one of the magnets and the front plate. Paintable versions are available


One magnet is supplied (the Levello system requires 3 magnets in total), the other two magnets are fixed to the IP65 plate and the Directional Insert

Decorators Cards

We supply decorators cards to protect the interior of the first fix housing from contamination from paint or plaster

5-Year Warrantee

Levello products come with a 5-yea5-year warrantee


First Fix Installation

Installation is simple and quick.

A reasonably accurate 62mm hole needs to be cut in the ceiling, our Holesaw Stabiliser is ideal for this. The supply cable is terminated to the connector and then the housing is inserted into the hole, twisting it clockwise to allow Housing anchors to lock into place. 

If painting after the housing has been installed please use the Painting cards provided to protect the inside of the housing from contamination.

 Housing Installation Guide


Second Fix Installation

Firstly, fit the lamp into the Directional Insert (see previous video), plug in the connector and fit the insert into the housing.

You can download the installation leaflet from the documents tab and more information is available on our Installation Guide page  - link below

PDF Guide

                   Second Fix Installation

Baffle Black or White or No Baffle or Special Baffle
Plate Finish Paintable or RAL 9010 or Custom Plate
Plate Shape Round or Obround
Lenses & Filters- None or Add Lenses
Directional Insert Installation guide.pdf
Directional GU10 IP65 Minimal Trim .pdf

Option's Documents